Speaker Test - Left Right Stereo, Phase and Sound Check Online
Speaker and Headphone Test
Check your speakers or headphones: does sound come from the right side, are the two channels wired the same way round, and how does the device handle low and high tones? All sounds are generated in your browser.
Turn your system volume down before the first sound, especially with headphones. The test starts quietly; raise the level slowly.
Ready. Press a button to play a sound.
Left and right channel
"Left" should come only from the left speaker or left ear cup, "Right" only from the right, "Both" from the middle. If Left is heard on the right, the headphones are on backwards (check the L/R marks) or the channels are swapped. If every button sounds the same from both sides, mono audio is on in your system settings or the device has only one speaker.
Phase (polarity) test
Sit between the speakers (or wear the headphones) and compare. In phase should sound solid and centred with full bass. Reversed phase sounds wide, hollow or "inside your head" with weaker bass. If the in-phase sound already seems like that, one speaker’s wires are probably connected the wrong way round (+ and - swapped).
Frequency sweep 20 Hz - 20 kHz
A pure tone glides from the deepest bass to the highest treble, quieter than the other tests. Listen for rattles, buzzing or sudden jumps in loudness. Small speakers often reproduce little below about 100-200 Hz, and many adults no longer hear the top of the range; that silence is your ears, not the speakers.
This page tests the device (speakers or headphones). To check how high and low you can hear, use the hearing test: Hearing Test
How the speaker test works
Every sound on this page is created on the fly by your browser, so there is nothing to download and no compression in the way. The channel test places a sound fully left, fully right or in the centre; the phase test plays the same noise on both channels, once normally and once with the right channel inverted; the sweep moves a pure tone across the audible range.
How to test your speakers
- 1 Turn the system volume down, then press Left, Both and Right. Each sound should come only from the side shown on the button.
- 2 Play the phase test twice: in phase, then reversed. The reversed version should sound clearly thinner and more spread out. If it does not, or the normal one already sounds hollow, check the speaker wiring.
- 3 Optionally play the sweep at a low level and listen for rattles, buzzing or dips. Press "Stop sound" at any time; leaving or hiding the page also stops every sound.
Headphones on backwards? Left and right explained
Stereo music, films and games place sounds between two channels, so a swapped pair moves footsteps, instruments and voices to the wrong side. Headphones are marked L and R, often on the headband or inside the ear cup; earbuds sometimes have a small bump on the left one. If the marks are right and the sides are still swapped, check the system sound settings, the audio driver’s tools or an adapter in the cable. When both sides sound identical, look for "mono audio" in the accessibility settings.
What the phase test reveals
A speaker cone pushes air forward when the signal is positive. If one speaker has its + and - wires swapped, it pulls back while the other pushes, and long bass waves from the two cancel each other out. The result is thin bass and a vague, wide image that does not sit between the speakers. The "Reversed phase" button simulates exactly that fault, so you know what to listen for. Fixing it is simple: swap the two wires on one speaker only.
Speaker test vs hearing test
Both use tones, but they answer different questions. This page checks the device: whether each channel works, whether the wiring is correct and how the speakers behave across the frequency range, with your ears as the judge. The hearing test turns that around and assumes the device is fine to estimate the range your ears pick up. When the sweep seems to fade out at the top, the hearing test helps you tell whether the speaker or your hearing sets the limit.
Pink noise, chord and sweep: why these sounds
The short chord is easy to locate and pleasant to hear repeatedly. Pink noise contains every frequency with equal energy per octave, which matches how we hear, so it shows whether a whole speaker plays and makes left-right and phase differences easy to judge. The sweep uses a single pure tone, so a rattle, a buzz or a missing band is heard exactly when the tone passes it. It plays quieter than the other sounds because the ear is most sensitive in the middle of the range.